Samsung Washer Error Codes and What They Mean

Read us the code and the model number. A tech tests the part behind that code on the visit and replaces it if it has failed.

A Samsung washer error code names the system that stopped the cycle: the fill, the drain, the door lock, the balance, a sensor or the motor. Read the code to Sacramento Appliance Care when you call, and we'll get a tech out to your Sacramento home.

Samsung prints one fault under several spellings, and the one you see depends on your model. A few letters are trickier, because they mean two different faults on two different washers.

The table gives each code's meaning as Samsung describes it, then what an appliance tech usually checks or replaces for that fault.

Samsung washers

Samsung Washer Error Code Table for Top-Load and Front-Load Models

Codes separated by commas are the same fault on different models. Starred codes mean different things on different washers.

Samsung washer codes, what they mean and what the tech looks at
Code on the displayWhat it usually meansWhat the tech checks or replaces
4C, 4E, nF, 1 4C Not filling: water isn’t entering the washer correctly. Water supply at the hoses, the inlet filter screens and the water inlet valve. A failed inlet valve gets replaced.
4C2, 4E2, CE, 14C2, nF1 Hot/cold error: the cold supply is extremely hot, usually because the hoses are swapped. Hose hookup at the inlets, then the inlet valve if the hookup is right.
5C, 5E, nd, SE, SC, 1 5C No drain: water isn’t draining at the correct speed, or at all. Drain hose setup, pump filter (front loaders), then the drain pump. A jammed or worn pump gets replaced.
OE, 0E, OC, 0C, 1 OC, 1 0C Overflow: too much water in the washer. Water level sensor and its hose, and whether the inlet valve shuts off fully.
LE, LC, 1E, 1C, LC1, 1 1C, 1 LC Water level or leakage: moisture where it doesn’t belong, or a sensor fault. Hoses, pump and tub seals for a leak, the drain hose for siphoning, and the water level sensor.
dE, dE1, dE2, dL, dS, d5, FL, LO, L0, dC*, dC1, 1 dC, 1dC1, 1dC4 Door error: the door isn’t detected as closed and locked. Door latch and strike, the door lock assembly and its wiring. A failed lock assembly gets replaced.
ddC, dC3 Add Door error: the small add-a-garment door isn’t closed and locked. Add Door latch and the switch that reads it as shut.
UE, Ub, U6, 1 Ub, 1U6, dC* Unbalanced load: the washer can’t finish the spin. On normal loads that still fail: shock absorbers, suspension rods, drum bearings and the motor speed sensor.
Ur Unbalanced load retry: the washer adds water and tries the spin again, so the cycle runs longer. If it ends in UE time after time, the same spin checks as UE.
Sd, SUd, 5d, 5UD, SUdS, 5Ud5 Excess suds: the washer has detected too much foam in the drum. If it shows on every load, the tech checks the drain pump, the drain path and the water level sensor.
SDC, 5DC The detergent drawer isn’t completely closed. Drawer track and the sensor that reads the drawer as shut.
E2, bE2, 6E2, BE2*, 8E2* Jammed button: a panel button reads as stuck. Control panel and its keypad board. A shorted key means a new panel board.
PF, 9C1, 9C2, 9E1, 9E2, 2E, UC, 19C1, 19C2, 3E* Voltage error: the washer isn’t getting the power it expects. Voltage at the outlet and the circuit, then the main control board.
tE, tE1, tC Temperature sensor error. The temperature sensor (thermistor) and its wiring. A failed sensor gets replaced.
HE, HE1, HC, Hr, 1 HC Heater error. Heater element, its wiring and the heater circuit on the control board.
3E*, 3C, E3, 1 3C Motor error (3E is a voltage error on some models). Motor, motor wiring and the hall sensor, then the control board that drives the motor.

Code meanings are summarized from Samsung's US support pages on washing machine error codes. The right-hand column is what an appliance tech usually checks for that fault; the part that gets replaced depends on what the tests show.

Read carefully

Samsung Codes That Mean Different Things on Different Models

Three codes trip people up because Samsung reuses them. For each one, the model number decides which fault the washer is reporting, so tell us the model when you call.

3E: voltage or motor

On some Samsung washers 3E is a voltage error, and the tech starts at the outlet and the circuit. On others it's a motor error, which points to the motor, its wiring or the hall sensor. A motor code that comes back after a restart usually means a part.

dC: door or unbalanced load

dC is a door error on some models and an unbalanced load on others. On a door model the tech checks the latch and the lock assembly. On an unbalance model it's the shocks, suspension and bearings.

BE2 or 8E2: stuck button or MEMS sensor

Some models use BE2 for a jammed control button. Others use it for a MEMS sensor error, which Samsung lists with its sensor faults. The first is a control panel repair. The second is a sensor the tech tests and replaces.

Repair visit

Diagnosing the Codes That Point to a Part

Some codes name a part or a circuit outright. Samsung's advice for these is service, and they tend to come back after a restart. This is where the tech starts on each one.

  • AE, AC and related codes: the control boards aren’t talking to each other. The tech checks the wiring harness between the display and main boards, then the boards. AE3 is a DR Ready modem error.
  • 8E, BE, 8C, BC family: MEMS sensor error; 8E or BE is a vibration sensor error on some models. The tech tests the sensor and its connection.
  • bE, 6E: motor speed sensor error. The tech checks the hall sensor on the motor and its wiring.
  • PE, PC and PE1, PC1: clutch position and clutch Hall signal errors on top loaders. The tech checks the clutch assembly and its sensor.
  • SF, IE, 5F: system error. Sr or 5r is a system relay error. Both point to the main control board.
  • 9C6, 9C7, 9C8: high temperature circuit and overcurrent errors. The tech checks the motor and heater circuits and the main board.
  • Motor, heater and sensor codes (3E, 3C, HE, tE): once they survive a restart, they point to the part named.
  • Door lock codes on a door that’s shut tight: usually the lock assembly itself.
Front-load washer with the lower access panel off and the drain pump filter removed, a small sock and a coin on a red towel

Drain codes

Diagnosing a 5C, nd or OE Drain Code

Samsung names the drain hose setup as the most frequent cause of drain problems, so that's where the tech starts. A hose pushed too far into the standpipe, or sealed airtight, siphons water out, and one that sits too shallow can slip loose. The setup can drift over years, so it gets checked even on an old install.

On a front loader the tech then opens the pump filter panel and clears the filter, where socks, coins and lint collect. Top loaders don't have a removable pump filter.

After that comes the drain pump. The tech runs a drain and listens to the pump, checks it for a jam, and replaces it if it's worn out. The same checks apply when a washer won't spin, because a Samsung washer has to drain before it spins.

Diagnostics

What Samsung's Built-In Test Cycle Checks

Many Samsung washers have a built-in test called Smart Install that steps through the lock, valves, drain and spin, and stops with a code at the first stage that fails. It's handy when a washer misbehaves without showing a code, and the tech can run it on the visit. These are the stages and the code each failure shows.

  • Door lock, display shows 1

    The lock clicks. A failure shows dC on front loaders or dC1 on top loaders, which points to the lock assembly.

  • Water valves, display shows 3, Co and Ho

    Bleach (front loaders), cold and hot valves each let water in. A failure at any of them shows 4C, which points to the inlet valve or the supply.

  • Agitation, display shows 6

    The drum rocks back and forth. On top loaders a failure shows 3C1, a motor or drive fault.

  • Drain, display shows 7

    The washer pumps out. A failure shows 5C, which points to the pump or the drain path.

  • High-speed spin, display shows 8

    The drum spins to top speed and slows. A failure shows 3C on front loaders or 3C4 on top loaders.

  • Door release and finish

    The lock releases and OK appears. No code means every stage passed.

The stage where the test stops tells the tech which part to look at first, which saves time on the visit.

Gloved hands turning the empty stainless drum of a front-load washer through the open door

Booking

Booking a Samsung Washer Repair

Samsung's own advice for nearly every code comes down to the same last step: if it keeps coming back, the washer needs service. When you call, tell us the model and serial number, the exact code and when in the cycle it shows. If the washer is still under warranty, tell us when you call.

The Samsung appliance repair page covers the brand's common washer and fridge faults, and washer repair in Sacramento covers every brand. California requires a written estimate before any repair; the repair cost guide explains what it covers.

Talk to us about a Samsung washer

Questions

Samsung Washer Code Questions

What does 4C mean on a Samsung washer?

It means water isn't getting into the washer the way it should. On the visit the tech checks the supply at the hoses, the inlet screens and the water inlet valve. A failed inlet valve is a common part to replace.

What does 5C or nd mean on a Samsung washer?

Both mean the washer can't drain at the right speed, or at all. The tech checks the drain hose setup, clears the pump filter on front loaders, then tests the drain pump. A worn or jammed pump is the usual part when the code keeps coming back.

Does the code tell the tech exactly which part to replace?

Not always. The code names the system that failed, like the fill, the drain or the door lock. The tech then tests the parts in that system to find the one at fault. That's why we ask for the model number and when in the cycle the code shows.

Can I keep running the washer while the code keeps coming back?

It's better to leave it off. A washer that keeps stopping on a fill, drain or leak code can leave water in the drum or on the floor. Tell us the code when you call, and we'll get a tech out to look at it.

Is a Samsung washer with an error code worth repairing?

Usually, when the code points to a pump, an inlet valve, a door lock or a sensor. A control board or motor on an older washer is a closer call. The repair cost guide shows typical washer repair medians, and the written estimate settles it.

Talk to us about the code

Tell us the Samsung model number, the exact code on the display and the point in the cycle where it stopped.

Call (916) 618-0484
Call (916) 618-0484